This guide summarizes the typical PolyDADMAC (polydiallyldimethylammonium chloride) dosing ranges and expected effects reported for common water-treatment applications. All figures are effective-dose values expressed on an active-solids basis (mg of polymer per litre of water, mg/L, equivalent to ppm). They are starting points for engineering design and must be calibrated to site-specific water quality through jar tests before full-scale dosing.
1. Typical Dosage by Water Type and Turbidity
Table 1 gives the commonly reported effective-dose windows for PolyDADMAC used as a primary coagulant or coagulant aid.
Water / Application | Raw Water Condition | Typical Effective Dose (mg/L) | Primary Effect / Target |
Potable water - low turbidity | < 10 NTU, low organic load | 0.05 - 0.5 | Colloid destabilization, low sludge |
Potable water - medium turbidity | 10 - 100 NTU | 0.5 - 1.0 | Turbidity & colour removal |
Potable water - high turbidity / algae | > 100 NTU, seasonal algae | 1.0 - 3.0 | Rapid floc settling, algae control |
Municipal secondary effluent | Polishing / tertiary | 1 - 5 | Residual suspended-solids & P removal |
Municipal primary / sludge thickening | Digested or waste sludge | 2 - 10 | Sludge dewatering aid |
Industrial - textile / dye wastewater | Highly coloured, anionic dyes | 5 - 20 | Charge neutralization, decolourization |
Industrial - paper mill white water | Fines & fillers | 1 - 8 | Retention & drainage aid |
Industrial - food / brewery effluent | High organic (COD) load | 5 - 25 | Organic & suspended-solids capture |
Mineral processing / mineral slurry | High solids, fine minerals | 0.1 - 2 % of dry solids | Flocculation & clarification |
Note: Dosages assume PolyDADMAC is dosed as a dilute working solution. Liquid commercial concentrates typically contain 10-50% active solids; convert the effective mg/L into a commercial-product dose by dividing by the solid-content fraction.
2. Working-Solution Dilution Reference
Table 2 summarizes recommended dilution of the commercial product before dosing, to ensure uniform mixing and avoid localized overdosing.
Application | Recommended Working Concentration | Dilution Water Temperature |
General water treatment | 0.1% - 0.5% (by active solids) | 10 - 40 degrees C |
Potable water polishing | 0.05% - 0.1% | 10 - 40 degrees C |
Sludge dewatering | 0.2% - 0.5% (or use emulsion at the belt) | 10 - 40 degrees C |
Coagulant blend (with PAC) | Per blend design, typically 0.1% - 0.3% | 10 - 40 degrees C |
3. Factors That Shift the Optimal Dose
· Raw-water turbidity and colour: higher suspended solids and natural organic matter (NOM) raise the demand for charge neutralization.
· pH: PolyDADMAC is stable across a wide pH range (roughly 4-10), but floc efficiency still varies with colloid charge state.
· Temperature: cold water slows collision and floc growth, often requiring a slightly higher dose or longer flocculation.
· Alkalinity and competing ions: high alkalinity or divalent cations can influence coagulant demand and blend ratios.
· Polymer characteristics: molecular weight and charge (solid content) of the grade affect the effective dose; compare on an active-solids basis.
· Point of injection and mixing energy: good rapid dispersion improves efficiency and reduces the required dose.
4. Determining the Optimal Dose - Jar Test Protocol
· Collect a representative raw-water sample and record turbidity, pH, temperature and colour.
· Prepare a dilute working solution of PolyDADMAC (e.g. 0.1% active solids).
· Dose a series of beakers across a bracketing range around the expected optimum (e.g. 0.1, 0.25, 0.5, 1.0, 2.0, 4.0 mg/L).
· Apply rapid mix (about 100-150 rpm for 1 minute), then slow mix (about 30-40 rpm for 15-20 minutes).
· Allow to settle (15-30 minutes), then measure residual turbidity, colour and, if relevant, phosphorus or COD in the supernatant.
· Plot residual turbidity versus dose; the optimum is the lowest dose meeting the target, noting restabilization at overdosing.
· Validate the selected dose in a pilot or full-scale test before committing to continuous dosing.
5. Use in Combination with Inorganic Coagulants
PolyDADMAC is frequently combined with inorganic coagulants (e.g. PAC, ferric chloride, poly-aluminium ferric chloride). In a typical composite scheme, the inorganic coagulant provides the bulk of charge neutralization and floc mass, while a small PolyDADMAC dose (often 0.1-1.0 mg/L, roughly 1-10% of the metal-salt mass) acts as a flocculant aid to bridge microflocs into larger, faster-settling aggregates. Typical practice adds the inorganic coagulant first at the rapid-mix point, followed by PolyDADMAC at the flocculation stage. This synergy improves floc size and regrowth resistance, lowers total chemical and sludge volumes, and is the most common configuration for medium- to high-turbidity surface waters.
6. Operating and Safety Notes
· Overdosing causes restabilization (charge reversal) and re-clouds the water and wastes chemical - jar-test calibration protects against overdosing.
· Where chloramine disinfection is used downstream, monitor for the reported potential of N-nitrosamine formation from PolyDADMAC residuals and optimize the dose.
· Use clean dilution water; prepare working solution fresh and avoid prolonged high-shear mixing, which degrades polymer chains.
· Store and handle per the supplier SDS; keep away from strong oxidizers and iron/copper alloys.
Disclaimer: Values in this guide are general industry reference ranges compiled for engineering guidance and are not product specifications. Actual optimal dosages vary widely with water quality, temperature, polymer grade and plant configuration, and must be established by jar testing and site trials. Always follow the polymer supplier technical data sheet and safety data sheet.
